Because the patient has mild systemic disease, he is ASA 2 and the procedure will be performed under local anaesthesia.

The following factors should be considered when requesting preoperative investigations:

Indications derived from a preliminary clinical examination
Whether or not a general anaesthetic will be used, the possibility of asymptomatic abnormalities, and the scope of the surgery.

No special investigations are needed if the patient has no history of significant systemic disease and no abnormal findings on examination during the nurse-led assessment.

There are different classes of electrical equipment that can be classified in the table below:

Class 1 – provides basic protection only. It must be connected to earth and insulated from the mains supply

Class II – provides double insulation for all equipment. It does not require an earth.

Class III – uses safety extra low voltage (SELV) which does not exceed 24 V AC. There is no risk of gross electrocution but risk of microshock exists.

Type B – All of above with low leakage currents (0.5mA for Class IB, 0.1 mA for Class IIB)

Type BF – Same as with other equipment but has ‘floating circuit’ which means that the equipment applied to patient is isolated from all its other parts.

Type CF – Class I or II equipment with ‘floating circuits’ that is considered to be safe for direct connection with the heart. There are extremely low leakage currents (0.05mA for Class I CF and 0.01mA for Class II CF)

The arterial cannula inserted should have parallel walls in order to reduce the risk of interruption of blood flow to distal limbs.

It is essential that the monitor used to display the arterial pressure waves has a frequency capacity of 0.5-40Hz. This is because the pressure waves are a combination of different sine waves of varying frequencies and amplitudes.

The diameter of the catheter is directly proportional to the natural frequency which is the frequency at which the system responsible for monitoring the waves resonates and amplifies the signals. This should be at least ten fold in comparison to the fundamental frequency. The diameter of the catheter is also inversely proportional to the square root of the system compliance, the tubing length and the fluid density within the system.

The presence of an air bubble, a clot or an easily malleable diaphragm and tube can result in wave damping. Increased damping will cause a reduction in the systolic pressure, and an increase in diastolic pressure. The maximum damping value of an appropriate monitoring system would be 0.64.

A rigid, non-malleable diaphragm and tubing can cause a resonance within the system. This resonance will result in an increase in the systolic pressure and a reduction in the diastolic pressure

Static lung compliance refers to the change in volume within the lung per given change in unit pressure. It is usually measured when air flow is absent, such as during pauses in inhalation and exhalation.

It is a combination of:

Chest wall compliance: normal value is 200 mL/cmH2O
Lung tissue compliance: normal value is 200 mL/ cmH2O

It is represented mathematically as:

1/Crs = 1/Cl + 1/Ccw

Where,

Crs = total compliance of the respiratory system
Cl = compliance of the lung
Ccw = compliance of the chest wall

Therefore in this case:

1/Crs = 1/200 + 1/200

1/Crs = 0.005 + 0.005 = 0.01

1/Ct = 0.01

Rearranging equation gives:

Ct = 1/0.01 = 100 mL/cmH2O.

Cardiopulmonary exercise testing (CPX, CPEX, CPET) is a non-invasive testing method used to determine the performance of the heart, lungs and skeletal muscle. It measures the exercise tolerance of the patient.

The parameters measured include:

ECG and ST-segment analysis and blood pressure
Oxygen consumption (VO2)
Carbon dioxide production (VCO2)
Gas flows and volumes
Respiratory exchange ratio (RER)
Respiratory rate
Anaerobic threshold (AT)

The anaerobic threshold (AT) is an estimate of exercise ability. Any measurement below 11 ml/kg/min is usually related with an increase in mortality, especially when there is a background of myocardial ischaemia occurring during the test.

Peak VO2 <20 mL/kg with a low AT have a correlation with postoperative complications and a 30 day mortality. The CPX test is used for risk-testing patients prior to surgery to determine the appropriate postoperative care facilities. The V slope measured in CPX testing represents VO2 versus VCO2 relationship. During AT, the ramp of V slope increases, but does not provide a picture of postoperative mortality.

Spirometry measures the total volume of air that can be forced out in one maximum breath, that is the total lung capacity (TLC), to maximal expiration, that is the residual volume (RV).

It is conducted using a spirometer which is capable of measuring lung volumes using techniques of dilution.

During spirometry, the following measurements can be determined:
Forced vital capacity (FVC)/vital capacity (VC): The maximum volume of air exhaled in one single forced breathe.
Forced expiratory volume in one second (FEV1)
FEV1/FVC ratio
Peak expiratory flow (PEF): the maximum amount of air flow exhaled in one blow.
Forced expiratory flow (mid expiratory flow): the flow at 25%, 50% and 75% of FVC
Inspiratory vital capacity (IVC): The maximum volume of air inhaled after a full total expiration.

Anatomical dead space is measured using a single breath nitrogen washout called the Fowler’s method.

Residual volume and total lung capacity are both measured using the body plethysmograph or helium dilution

The functional residual capacity is usually measured using a nitrogen washout or the helium dilution technique.

Closing capacity refers to volume of gas within the lungs at which the conducting small airways begin to close, that is, the point during expiration when small airways close.

It is calculated mathematically as:

Closing capacity = Closing volume (CV) + Residual volume (RV)

Functional residual capacity (FRC) is the volume of gas still present within the lungs post expiration.

Closing capacity is lower than the functional residual capacity in younger adults, but begins to rise to eventually equal, and then exceed it with increasing age (at about middle age), increasing intrabdominal pressure, decreasing blood flow in the pulmonary system and parenchymal disease within the pulmonary system.

Malignant hyperthermia (MH) is a autosomal dominant inherited medical condition which predisposes affected individuals to a clinical syndrome of hypermetabolism which involves abnormal ryanodine receptors in skeletal muscle causing a deregulation of calcium in muscle.

It is a life threatening condition requiring immediate medical intervention. It often lies dormant until triggered in susceptible individuals mostly by volatile inhaled anaesthetic agents and succinylcholine which is a muscle relaxant.

The signs and symptoms of MH are related to this hypermetabolism, which includes an increase in carbon dioxide production, metabolic and respiratory acidosis, accelerated oxygen consumption, heat production, activation of the sympathetic nervous system, hyperkalaemia, disseminated intravascular coagulation (DIC), and multiple organ dysfunction and failure.

Early signs of MH to look out for in patients includes an uptick in end-tidal carbon dioxide (even with increasing minute ventilation), tachycardia, muscle rigidity, tachypnoea, and hyperkalaemia. Later signs include fever, myoglobinuria, and multiple organ failure.

In vitro muscle contracture test (IVCT) is the standard for determining individual susceptibility to MH. It is conducted by measuring the force of muscle contraction after exposing the patient’s muscle sample to halothane and caffeine., the sample is normally taken from the vastus medialis or lateralis under regional anaesthesia.

Since an arterial pressure transducer, and every other measuring apparatus, is prone to errors due to offset and gradient drifts, regular calibration is required to maintain accuracy of the instrument. The two-point calibration pressure values of 0 mmHg and 200 mmHg are within the physiologic range and can best compensate for the gradient drift.

There are different types of temperature measurement. These include:

Thermistor – this is a type of semiconductor, meaning they have greater resistance than conducting materials, but lower resistance than insulating materials. There are small beads of semiconductor material (e.g. metal oxide) which are incorporated into a Wheatstone bridge circuit. As the temperature increases, the resistance of the bead decreases exponentially

Thermocouple – Two different metals make up a thermocouple. Generally, in the form of two wires twisted, welded, or crimped together. Temperature is sensed by measuring the voltage. A potential difference is created that is proportional to the temperature at the junction (Seebeck effect)

Platinum resistance thermometers (PTR) – uses platinum for determining the temperature. The principle used is that the resistance of platinum changes with the change of temperature. The thermometer measures the temperature over the range of 200°C to1200°C. Resistance in metals show a linear increase with temperature

Tympanic thermometers – uses infrared radiation which is emitted by all living beings. It analyses the intensity and wavelength and then transduces the heat energy into a measurable electrical output

Gauge/dial thermometers – Uses coils of different metals with different co-efficient of expansion. These either tighten or relax with changes in temperature, moving a lever on a calibrated dial.